Vacuum Belt Filter

Vacuum Belt Filter

Basic Info DU75-3900 Filter Area 24 M2 Effective Width of Filter Belt 2400mm Rubber Belt Running Speed 2-8m/Min Vacuum Box Length 10.4m Main Drive Power 11kw Main Drive Reducer Model Ab4hh8 Main Drive Reducer Output Torque 20000n*M Main Drive Motor Operating Frequency 10-50Hz Filter Cloth...
Chat Now

Product Details

Basic Info


Filter Area

24 M2

Effective Width of Filter Belt


Rubber Belt Running Speed


Vacuum Box Length


Main Drive Power


Main Drive Reducer Model


Main Drive Reducer Output Torque


Main Drive Motor Operating Frequency


Filter Cloth Washing Water Pressure

0.4MPa or More

Filter Cloth Washing Water Consumption

4-6 M3/H



Transport Package

1*40′ Container



I. Introduction:

The belt filter press is a continuous-feed dewatering device that applies chemical conditioning, gravity draining, and mechanical pressure to dewater sludge. Rubber belt type vacuum filter takes filter bag as filter medium, adopt material gravity and vacuum suction to separate solid and liquid materials. It is adopted ring rubber belt as a vacuum chamber. The vacuum chamber continuously running by motor, filter cloth are layup to the rubber belt and running along with the belt, the rubber belt with friction belt create a water-tight seal. Slurry are distributed on filter cloth by distributing device When the vacuum chamber is switched on vacuum system, it will create a vacuum area on rubber belt, Filtrate liquor pass through filter cloth by horizontal grooves on rubber belt, then get together and go into the vacuum chamber by micro pore, Solid powder are holding on filter cloth, then create a filter cake. The liquid which have got into vacuum chamber be discharged by steam-water separator. Move along with the rubber belt, preformed filter cake get into washing section and suck dry section. Finale filter cloth and rubber belt are divided, the filter cake are discharged from discharging roller. The filter cloth which discharge filter cake are washed ,then can be re-used, re-access to filtrate area by a sets of supportive roller and rectify device, begging a new cycle.

II. Feature

1. Widely used in solid-liquid separation 

2. Ideal equipment for sludge dewatering

3. Ring type abrasive belt is set between vacuum container and the rubber belt, water is used to air proof and lubricate which can keep stable and higher vacuum degree, good for stable operation state.

4. Rubber belt is supported by air cushion or water to reduce the resistance and is good to prolong service life of the rubber belt.

5. The whole structure adopts module design which can be consolidated freely, convenient for transportation and installation.

6. Vacuum balance automatic discharging tank or steam-liquid separator is set to carry out zero potential difference automatic discharging or high potential difference discharging to satisfy requirements from different working states

7. The control system uses PLC technology to carry out PID regulation, provide safety guarantee of running and supervision of the procedure.

III. Advantages and characteristics of belt press:

1. Continuous and fully automatic operation

2. High reduction of sludge volume for saving of transport cost

3. High dewatering performance due to the convenient arrangement of the rollers

4. Using the latest advanced technology, add one more independent concentrated device based on normal type belt press, significantly increased the ability of water removal.

5.  8-15% lower flocculation consumption with combination of dynamic and static flocculation reactor.

6. High working capacity (150% of normal type), low moisture content of filter cake (10% less than normal type), low working cost(30% lower than normal type)

7. The frame is made of high quality seamless square steel pipe(10#-12#) with sandblast and high strength fluorin-carbon finish, makes anticorrosive ability keep more than 8 years.

8. The main body are made of stainless steel (304), including main and assistant rollers, fender, flume, waterproof cover, muzzle and sheets, etc.

9. High quality bearing with full airproof bearing seat, available to run more than 3 years.

10. Extrusion and transmission rollers are made of seamless steel pipe with anti-wearing rubber outside, valid to work more than 5 years.

IV. The belt filter press can be used in the following industrial sectors:

* municipal plants

* pulp and paper industry

* leather industry

* textile processing

* fruit and vegetable processing Kirchen/Germany.

* steel works and roller mills

* sugar industry

* bio-water processing

* Ceramic industry

* Mining industry.

V . Main technical parameter:


Filter area24 m2

Effective width of filter belt2400mm

Rubber belt running speed2-8m/min

Vacuum box length10.4m

Main drive power11KW

Main Drive Reducer ModelAB4HH8

Main drive reducer output torque20000N*M

Main drive motor operating frequency10-50HZ

Filter cloth washing water pressure0.4MPa or more

Filter cloth washing water consumption4-6 m3/h

Vacuum box lubrication water pressure0.15MPa

Vacuum box lubrication water consumption15-50L/min

Vacuum pump model2BEA-353  

Vacuum pump input power90KW

Power connectionbelt/pulley

Water consumption of vacuum pump2.0-4.0m3/h

Effective Vacuum Negative Pressure0.02-0.07MPa

Filter cloth tension force0-2KN/M

Correction limit rang60mm

Correcting air bag stroke150mm

Correcting air pressure0.2-0.3 MPa

Steam-water separator volume0.3m3

Steam and water separation conversion time settingInto the liquid: 6-30S          Discharge: 8-30S

Total length14.3m

Total width5.1m

Treating capacity (dry basis gypsum)24Ton/Hour